AUXITO for 2018-2019 Ford F-150 LED Red Brake Light Bulb

Save 44%
$50.00
$27.99

AUXITO for 2018-2019 Ford F-150 LED Red Brake Light Bulb

FREE Shipping

1 Year Warranty

  • Each 3156/3157 bulb powered by 16 pcs high power 3030 led chips, low power consumption but high light output. HD glass lens for stronger light penetration
  • DC 9V to 18V wide-range voltage design, built-in constant intelligent IC driver, no digital and VHF radio signal interference. Aluminum circuit board, high effective heat dissipation
  • Plug and play easy installation,no polarity design, compatible for both standard and ck socket. Fit socket: 3156, 3056, 3356, 3456, 4156, 3047, 3157, 3157A, 3057, 3155, 3157NA, 3357, 3457, 3457A, 4057, 4114, 4157, etc
  • Brilliant Red Color. It can be used for brake light, tail light, turn signal blinkers, etc. The 50w 6ohm load resistor or flasher relay may be needed to prevent the hyper flash or the bulb does not blink for vehicles with built-in CANbus system
  • Detail
  • Review

3157 red brake light led bulbs

3157 red tail led bulbs

Features and Performance Details

Each bulb has 16pcs high power 3030 LED chips for perfect beam pattern, high light output but low consumption
Wide-range voltage and intelligent constant current IC driver to avoid digital and VHF radio signal interference
HD glass projector provides a stronger light penetration for better lighting experience
Heat-resistant Aluminum circuit board for better transfer efficiency. Solid alloy body for better heat dissipation and longer lifespan
No polarity design, and compatible for both standard and CK socket. Used for brake light, tail light, turn signal lights, etc
Comparable to OEM sized halogen bulbs and fit directly into sockets such as: 3156, 3056, 3356, 3456, 4156, 3047, 3157, 3157A, 3057, 3155, 3157NA, 3357, 3457, 3457A, 4057, 4114, 4157, etc
Important Note

Compatible with most vehicles. Some vehicles with a built-in canbus system might throw the error code. The 50w 6ohm load resistor or flasher relay may be needed to prevent the hyper flash or the bulb does not blink for vehicles with a built-in canbus system.

 

FAQ

Question: Do these have built-in load resistors to avoid hyper flashing? Fitting 4057 plug?
Answer: Instead of installing numerous resistors (which can get quite hot) make it easy on yourself. Replace the standard turn signal flasher with an electronic flasher.

I installed LED turn signals on my 2004 f250. Had a hyper flash, walked into parts store, bought an electronic flasher - all good for the past 4 years.


Question: Will it require resistors on a 2013 Silverado?
Answer: I can’t say for certain, but I would say yes. Every car I’ve put these in I’ve had to add resistors, they are cheap and easy to install! They are great bulbs btw!

Question: Will this fit my 1998 Chevy Silverado front turn signals
Answer: Depending on what base that you have on your original lights, from what I know they have the cylindrical push and twist the base and these lights are for the push-in base.

Question: Will this work for my 2010 Camaro? Its says it only works on dual-function lights

Question: Will these cause car to think that lightbulb is out? Aka rapid blink? Does Aka need a resistor?
Answer: I had no dash lights come on saying I had burnt out bulbs, I did have to add resistors to take care of the rapid flash. 2007 mustang.

Question: are these brighter than factory HID lights on cars?
Answer: Yes, much brighter! Also, keep in mind that these are switchbacks! Meaning that your running lights will be white until you got the turn signal then they blink orange after you turn the light goes back to white. You will also need to install load equalizers to prevent hyper flash. I have them in my 16 tundras and love them!

Question: Do I need resistors for a 2009 grand Cherokee Laredo?
Answer: If the Jeep didn't come with LEDs from the factory, you will most likely need resistors for the blinkers. If you have a socket that just lights up when you turn on the lights, these will work fine.

You recently viewed

Clear recently viewed